Dv 10110

Disponível somente no TrabalhosFeitos
  • Páginas : 5 (1108 palavras )
  • Download(s) : 0
  • Publicado : 17 de julho de 2012
Ler documento completo
Amostra do texto
Technical Data Sheet
1/26/2012

Plastic Steel Putty (A)
Description:

A steel-filled epoxy putty that cures at room temperature and is designed for filling, rebuilding, and bonding metal surfaces

Intended Use:

Patching and repairing areas where welding or brazing would be undesirable or impossible

Product
features:

Applies easily to vertical surfaces
Machinable to metallicfinish
Bonds to aluminum, concrete, and many other metals
Resistant to chemicals and most acids, bases, solvents, and alkalis

Limitations:

Not recommended for long term exposure to concentrated acids or to organic solvents

Typical
Physical
Properties:

Technical data should be considered representative or typical only and should not be used for specification purposes.
Cured 7 days @75° F
Adhesive Tensile Shear
Coefficient of Thermal Expansion
Color
Compresive Strength
Coverage/lb
Cured Hardness
Cured Shrinkage
Dielectric Constant
Dielectric Strength
Flexural Strength
Functional Cure
Mix Ratio by Volume
Mix Ratio by Weight
Mixed Viscosity
Modulus of Elasticity
Pot Life @ 75F
Recoat Time
Solids by Volume
Specific Gravity
Specific Volume
TemperatureResistance
Thermal Conductivity

Surface
Preparation:

TESTS CONDUCTED
Cure Shrinkage ASTM D 2566
2800 psi
Adhesive Tensile Shear ASTM D 1002
48 [(in)/(in) x ° x 10(-6)
F)]
Dielectric Strength, volts/mil ASTM D 149
Grey
Dielectric Constant ASTM D 150
8260 psi
Flexural Strength ASTM D 790
48 sq. in @ 1/4 in.
Compressive Strength ASTM D 695
85D
Cured Hardness Shore D ASTM D 2240
Coef.of Thermal Expansion ASTM D 696
0.0006 in./in.
Thermal Conductivity ASTM C 177
67.5
Modulus of Elasticity ASTM D 638
30 volts/mil
5600 psi
16 hrs
2.5:1
9:1
Putty
8.5 x 10(5) psi
45 min.
2-4 hrs
100
2.33 gm/cc
11.9 in.(3)/lb.
Wet: 120° Dry: 250°
F;
F
1.37 [(cal) / (sec. x cm x ° x 10 (-3)
C)]

1. Thoroughly clean the surface with Devcon® Cleaner Blend 300 to remove all oil,grease and dirt.
2. Grit blast surface area with 8-40 mesh grit, or grind with a coarse wheel or abrasive disc pad, to create increased
surface area for better adhesion (Caution: An abrasive disc pad can only be used provided white mesh is revealed).
Desired profile is 3-5mil, including defined edges (do not "feather-edge” epoxy).
Note: For metals exposed to sea water or other salt solution,grit-blast and high-pressure-water-blast the area, then leave
overnight to allow any salts in the metal to “sweat” to the surface. Repeat blasting to “sweat out” all soluble salts. Perform
chloride contamination test to determine soluble salt content (should be no more than 40ppm).
3. Clean surface again with Devcon® Cleaner Blend 300 to remove all traces of oil, grease, dust or other foreignsubstances from the grit blasting.
4. Repair surface as soon as possible to eliminate any changes or surface contaminants.
WORKING CONDITIONS: Ideal application temperature is 55° to 90° In cold working conditions, directly heat repair
F
F.
area to100-110° prior to applying epoxy and maintain at this temperature during product cure to dry off any moisture,
F
contamination or solvents, as wellas to achieve maximum performance properties.

ITW Devcon, 30 Endicott Street, Danvers, MA 01923

Tel:(978) 777-1100

Fax:(978) 774-0516 www.devcon.com

Mixing
Instructions:

---- It is strongly recommended that full units be mixed, as ratios are pre-measured. ---1. Add hardener to resin.
2. Mix thoroughly with screwdriver or similar tool (continuously scrape material away from sidesand bottom of container)
until a uniform, streak-free consistency is obtained.
INTERMEDIATE SIZES (1,2,3 lb. units): Place resin and hardener on a flat, disposable surface such as cardboard,
plywood or plastic sheet. Use a trowel or wide-blade tool to mix the material as in Step 2 above.
LARGE SIZES: (25 lb., 30 lb., 50 lb. buckets): Use a T-shaped mixing paddle or a propeller-type Jiffy...
tracking img