Placa mae

Páginas: 99 (24549 palavras) Publicado: 17 de setembro de 2012

FCC-B Radio FRequenCy inteRFeRenCe StateMent
this equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 5 of the FCC rules. these limits are designed to provide reasonable protection against harmful interference in a residential installation. this equipment generates, uses and can radiate radio frequency energy and, if notinstalled and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the measures listed below. Reorient or relocate the receiving antenna. increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ television technician for help. notice  the changes or modifications not expressly approved bythe party responsible for compliance could void the user’s authority to operate the equipment. notice 2 Shielded interface cables and a.C. power cord, if any, must be used in order to comply with the emission limits.

VoiR La notiCe d’nStaLLation aVant de RaCCoRdeR au ReSeau.

Micro-Star international MS-7529
this device complies with Part 5 of the FCC Rules. operation is subject to thefollowing two conditions: () this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

PaRt nuMBeR

CoPyRiGHt notiCe
the material in this document is the intellectual property of MiCRo-StaR inteRnationaL. We take every care in the preparation of this document, but noguarantee is given as to the correctness of its contents. our products are under continual improvement and we reserve the right to make changes without notice.

all trademarks are the properties of their respective owners.

■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■

MSi® is registered trademark of Micro-Star int’l Co.,Ltd. nVidia® is registered trademark of nVidia Corporation. ati® is registeredtrademark of ati technologies, inc. aMd® is registered trademarks of aMd Corporation. intel® is registered trademarks of intel Corporation. Windows® is registered trademarks of Microsoft Corporation. aMi® is registered trademark of american Megatrends inc. award® is a registered trademark of Phoenix technologies Ltd. Sound Blaster® is registered trademark of Creative technology Ltd. Realtek® isregistered trademark of Realtek Semiconductor Corporation. JMicron® is registered trademark of JMicron technology Corporation. netware® is a registered trademark of novell, inc.

ReViSion HiStoRy
Revision V.2 Revision History Release for PCB .6 date May 2009



SaFety inStRuCtionS
■ ■ ■ ■ ■
always read the safety instructions carefully. keep this user Manual for futurereference. keep this equipment away from humidity. Lay this equipment on a reliable flat surface before setting it up. the openings on the enclosure are for air convection hence protects the equipment from overheating. do not cover the openings. before connecting the equipment to the power inlet. anything over the power cord.

■ Make sure the voltage of the power source and adjust properly 0/220V ■Place the power cord such a way that people can not step on it. do not place ■ always unplug the Power Cord before inserting any add-on card or module. ■ all cautions and warnings on the equipment should be noted. ■ never pour any liquid into the opening that could damage or cause electrical shock.

■ if any of the following situations arises, get the equipment checked by a service personnel: ○ ○...
Ler documento completo

Por favor, assinar para o acesso.

Estes textos também podem ser interessantes

  • Placa Mãe
  • Placa mãe
  • placa mãe
  • placa mae
  • Placa mãe
  • Placa mãe
  • placa mae
  • Placa mae

Seja um membro do Trabalhos Feitos