Ccna 2

Disponível somente no TrabalhosFeitos
  • Páginas : 30 (7396 palavras )
  • Download(s) : 0
  • Publicado : 1 de dezembro de 2012
Ler documento completo
Amostra do texto
Fi n a l E xa m V 4 .0 A n swe rs | CCNA A n swe rs - CCNA E xa m - CCNA E xa m s

CCNA Answers – CCNA Exam – CCNA Exams
CCNA Exam Answers, CCNA Final Exam Answers, CCNA Module Answers, CCNA Chapter Answers, CCNA
Test Answers, CCNA Questions and Answers, CCNA 1 Answers, CCNA 2 Answers, CCNA 3 Answers, CCNA 4
Answers, CCNA v4 Answers
Home
About
Contact
VLSM Calculator
CCNA Forums
Ads byGoogle

Jac k Johns on

Cis c o Router

Cis c o CCNA

Network Router

CCNA 2 Final Exam V4.0 Answers
Posted in CCNA 2 - Routing Protocols and Concepts (V4.0) - 22 April 2010 - 7 comments - 162,779 views
1.

Refer to the exhibit. Given the topology shown in the exhibit, what three commands are needed to configure EIGRP on
the Paris router? (Choose three.)
Paris(config)# routereigrp 100
Paris(config)# router eigrp
ccn a a n swe rs.co m /ccn a -2 -fi n a l -e xa m -v4 -0 -a n swe rs/

Fi n a2 7 /11 /1 2 4 .0 A n swe rs | CCNA A n swe rs - CCNA E xa m - CCNA E xa m s
l E xa m V

Paris(config- router)# network 192.168.6.0
Paris(config- router)# network 192.168.7.0
Paris(config- router)# network 192.168.8.0
Paris(config- router)# network 192.168.9.0

2. In a labtest environment, a router has learned about network 172.16.1.0 through four different dynamic routing
processes. Which route will be used to reach this network?

D 172.16.1.0/24 [90/2195456] via 192.168.200.1, 00:00:09, Serial0/0/0
O 172.16.1.0/24 [110/1012] via 192.168.200.1, 00:00:22, Serial0/0/0
R 172.16.1.0/24 [120/1] via 192.168.200.1, 00:00:17, Serial0/0/0
I 172.16.1.0/24 [100/1192] via192.168.200.1, 00:00:09, Serial0/0/0

3. Which routing protocol maintains a topology table separate from the routing table?
IGRP
RIPv1
RIPv2
EIGRP

ccn a a n swe rs.co m /ccn a -2 -fi n a l -e xa m -v4 -0 -a n swe rs/

2 /2 7

Fi n a2 7 /11 /1 2 4 .0 A n swe rs | CCNA A n swe rs - CCNA E xa m - CCNA E xa m s
l E xa m V

4. Refer to the exhibit. R1 and R2 are unable to establish anadjacency. What two configuration changes will correct the
problem? (Choose two.)
Set a lower priority on R2.
Configure the routers in the same area.
Set a lower cost on R2 compared to R1.
Add a backup designated router to the network.
Match the hello and dead timers on both routers.

5. Which statement is true about the metrics used by routing protocols?
A metric is a value used by aparticular routing protocol to compare paths to remote networks.
A common metric is used by all routing protocols.
The metric with the highest value is installed in the routing table.
The router may use only one parameter at a time to calculate the metric.

6. Refer to the exhibit. Although R2 is configured correctly, host A is unable to access the Internet. Which two static
routes can beconfigured on R1 to enable Internet connectivity for host A? (Choose two.)
ip route 0.0.0.0 0.0.0.0 Fa0/0
ip route 0.0.0.0 0.0.0.0 Fa0/1
ip route 0.0.0.0 0.0.0.0 10.1.1.1
ip route 0.0.0.0 0.0.0.0 10.1.1.2
ip route 209.165.202.0 255.255.255.0 10.1.1.1
ccn a a n swe rs.co m /ccn a -2 -fi n a l -e xa m -v4 -0 -a n swe rs/

3 /2 7

Fi n a2 7 /11 /1 2 4 .0 A n swe rs | CCNA A n swe rs - CCNA Exa m - CCNA E xa m s
l E xa m V

ip route 209.165.202.0 255.255.255.0 10.1.1.2

7. Refer to the exhibit. Host A is unable to access the Internet. What is the reason for this?
The IP address of host A is incorrect.
The default gateway of host A is incorrect.
The Fa0/1 interfaces of the two routers are configured for different subnets.
The subnet mask for the Fa0/0 interface of R1 isincorrect.

8.

Refer to the exhibit. Two routers are unable to establish an adjacency. What is the possible cause for this?
The two routers are connected on a multiaccess network.
The hello and dead intervals are different on the two routers.
They have different OSPF router IDs.
They have different process IDs.

9.

2 7 /11 /1 2

Refer to the exhibit. R1 knows two routes, Path A and...
tracking img